HOME > Product Information > Conveyor Equipment > Light Conveyor > Belcon Mini > Belcon Mini III / DMJ
Belcon Mini IIIDMJ
Short length type
Extremely miniature type with a minimum length of 250mm.
About the various icons
specification
 DMJ |
 30 |
 D |
 R |
 50 |
 D18 |
 R |
 09 |
 X |
*Colored text is semi-standard.
|
Model code | DMJ (Center Drive Short Length) | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
|
Nominal width | 10 | 15 | 20 | 25 | 30 | 35 | 40 | 50 | 60 | |
| BW Actual belt width (mm) | 97 | 147 | 197 | 247 | 297 | 347 | 397 | 497 | 597 | ||
| FW Frame width (mm) | 145 | 195 | 245 | 295 | 345 | 395 | 445 | 545 | 645 | ||
|
Captain (cm) | Nominal width 10 to 25: MIN.25 to MAX.60 Nominal width 60: MIN. nominal width to MAX. 60 |
|||||||||
| Standard Belt | Resin belt with anti-snake bars (1 ply) | ||||||||||
| End Pulley Diameter | φ27.2 | ||||||||||
|
Drive unit type *1 | D: Subscript | |||||||||
|
Mounting direction of drive unit *1 | R: Right side of conveying direction L: Left side of conveying direction | |||||||||
|
Speed symbol | Please refer to the "Speed Symbol/Conveyor Speed Table" | |||||||||
|
Controller installation direction *1 *2 | R：搬送方向右側 L：搬送方向左側 T：コントローラ無し※3 | |||||||||
|
Motor output *4 | N: constant speed | 04:40W 06:60W 09:90W | ||||||||
| D：ブラシレス変速 | 04：40W 09：90W | ||||||||||
| F：インバータ変速 ※5 | 04:40W 06:60W 09:90W | ||||||||||
|
Input Power | X: 100V single phase Y: 200V single phase Z: 200V three phase | |||||||||
| Payload *6 | MAX.15kg/unit | ||||||||||
- Please check here for details
- The drive unit and controller are installed in the same direction.
- T：コントローラ無しは、N：定速の入力電源Z：200V三相のみ適用します。
- The high-speed motor output is 90W.
- F：インバータ変速の場合、コントローラは別置きまたは脚に取付となります。
- For motor output, refer to "Guideline for payload."
- We can also manufacture products other than the standard specifications, so please contact us for details.
- To prevent tipping over, please use it by anchoring it or connecting it to the front and rear devices.
Dimensions
- 1.F：インバータ変速の場合、コントローラは別置きまたは脚に取付けとなります。
2.フレーム断面、モータ突出寸法(上図A寸法)はこちらをご参照ください。
3.コントローラ突出寸法は、弊社営業部へお問い合わせください。
Estimated payload
Note: The graph/table below shows the transport mass when the load is distributed horizontally. 
Motor output standard setting list
Note: If you need to upgrade the motor output depending on the speed, payload, and other operating conditions, please select the motor output using the payload graph above.
Speed symbol/Conveyor speed table
- 1. 色文字 は準標準速度を表します。
2. 定速とインバータ変速の速度は、負荷により±10%程度変動します。
3. ブラシレス変速時の負荷による速度変動は±1%以内です。